How to build a shelving unit for a car
You can build a shelving unit for your car yourself from aluminium profiles with a clamping slot. Below is the procedure from finding out the vehicle's dimensions to anchoring, and what is worth settling in advance. Anyone who does not want to build from scratch can order a ready-made assembly or a made-to-measure shelving unit.
Videa
First find out what you carry and what it is carried in
A shelving unit is built according to what you carry in the car. Write a list of items and divide them into heavy, light, long, fragile and expensive ones. Measure or photograph the most important cases, boxes and tools and decide what you need to have at hand fastest.
Where to put the shelving unit in the car
A side shelving unit runs along the left or right wall of the cargo area. A shelving unit behind the cab stands directly behind the partition that separates the cab from the cargo area. If a shelving unit has shelves on one side only, it loads the vehicle unevenly. Balance heavy items with the opposite side or the centre.
How tall the shelving unit can be
The height of the shelving unit is not determined by the ceiling of the cargo area but by the opening of the rear doors through which it is carried into the car. The shelving unit is loaded through the rear doors and therefore has to fit through them. For the design you need to know the make, model, year of manufacture and the length and height of the body. These are used to find the dimensions of the cargo area and the height of the rear opening.
What to build the shelving unit from
A practical assembly looks like this: the load-bearing structure is aluminium, the bottoms and sides of the shelves are plywood or plastic, the drawers for the heaviest items are steel and the boxes are plastic. You will find more about materials in the chapter Materials: aluminium, steel, wood and plastic.
- Aluminium profiles. They are light, do not rust and have a clamping slot along the full length. Shelves, drawers and your own additions can be fixed into it anywhere without drilling into the profile. The modular kit for cars has System 30, 40 and 45. System 30 is a light universal version, System 40 is intended for vans of height H1 and System 45 for taller vans H2 and H3 and more demanding loads.
- Shelf panels. Film-faced plywood is rigid, cuts well to size and its film protects it against moisture. Plastic is lighter and does not absorb water.
- Drawers and boxes. Steel drawers suit the heaviest tools. Plastic boxes and Euro boxes slide into pull-outs with a spring lock.
Weight and load distribution
Every kilogram taken up by the racking is deducted from the vehicle's payload. Heavy items belong low and as close to the vehicle axis as possible, light ones up high and at the edges. The rear axle has to be watched separately, because a vehicle can be within its overall limit and still overload the rear axle when everything is at the back. There is more in the chapter Weight and payload of the van.
Anchoring to the vehicle body
The shelving unit has to be firmly connected to the car, otherwise it is just a pile of material. Anchoring requires drilling into reinforced parts of the vehicle body, because vans have very few original anchor points. Drilling into reinforced parts of the body is common, expected and in line with homologation requirements. The aluminium profile itself is not drilled again.
Do not anchor into thin sheet metal without reinforcement, do not skimp on washers and large surfaces that spread the force, and do not drill where cables, hoses or tanks run. With electric vehicles you must also find out where the high-voltage wiring and battery run, and drill only into approved locations. The details are in the chapter Anchoring vehicle racking.
Securing the load in the shelving unit
The most common mistake is that heavy items are secured and light small items lie loose in open compartments. A light item flies in an impact too. So close the compartments, give them doors, fold-down fronts, straps or rubber bands, or use boxes with lids. Long items, for example pipes, battens or ladders, should have their own holders and be fixed at both ends. There is more in the chapter Safety and load securing.
Conversion, technical inspection and insurance
The law does not expressly mention racking made of aluminium profiles. There is therefore no blanket rule that a shelving unit installation requires approval, or that it does not. What matters is the nature of the racking and the specific vehicle. It is sensible to go through it right at the design stage and, where needed, to ask the municipal authority of the municipality with extended powers or a testing station in advance. We also recommend informing your insurer about the racking. For a specific vehicle and assembly, the decision always lies with the authority, the testing station and your insurer. There is more in the chapter Van racking, technical inspection (STK) and insurance.
DIY or with professional installation
Anyone who builds a shelving unit themselves takes on responsibility for its strength and anchoring, for how the assembly behaves under braking, and for making sure it is properly recorded with the authorities and the insurer. A structure made of profiles can be assembled yourself and many customers do so. It helps to have basic tools, a level surface and a little patience. Joints may settle slightly after the first loading, so check that they are tight after the first trips.
Professional installation is an optional service. We carry it out in Prague, in Slavičín in the Zlín region or at your premises. It includes drilling into reinforced parts of the vehicle body, anchoring the structure and testing the function of the pull-outs and locks.
Anyone who does not want to build from scratch can choose a ready-made example assembly among the shelving units for cars and vans. We design a made-to-measure shelving unit from a photograph of the cargo area, a sketch or a description, and prepare a 3D model that you can view and have adjusted.
Zadejte nám nezávaznou poptávku:
Napište nám, ozveme se vám na uvedený e-mail.