Van racking by vehicle

Professional van racking by vehicle is a signpost for anyone who knows which van they own and wants racking made exactly for it. Choose a make – Citroën, Fiat, Mercedes, Volkswagen, Ford, Toyota, Peugeot, Renault, Opel or Iveco – and the page will lead you to the model and the specific body type.

Racking here is not a ready-made product with fixed dimensions: we build it to the millimetre around the tools, cases and crates you actually carry in the vehicle.

How to choose racking for your vehicle

The procedure is simple: first the make, then the model and finally the body version. For commercial vehicles the same model exists in several length and height variants (marked with the letters L and H, for example L2H2) and often in several generations. These details tell you which assembly to look for.

  • Model and generation – for example the Fiat Doblò up to 2022 and the newer Doblò, or the Mercedes Sprinter before 2018 and after it.
  • Body length and height – designations L1 to L5 and H1 to H4, depending on the model.
  • Version and drive – electric versions, such as the ë-Jumpy or eVito, are handled separately; for some large vehicles the body is also divided according to whether it has front-wheel or rear-wheel drive.

On the page for each make you will find its models and, for each of them, ready-made assemblies for the individual bodies. Where there is no ready-made assembly yet, the racking can be ordered as a made-to-measure job with any dimensions.

Why the specific vehicle matters

Made-to-measure racking means that we make the storage system to the millimetre according to the requirements that come out of a consultation with you. We adapt to your tools, cases and ideas, and because bodies differ from model to model, the shelving unit has to fit your cargo space exactly. No part is therefore set in stone: anything in the assembly can be moved, enlarged, reduced or left out according to what you actually carry in the vehicle.

Shared platform: Ducato, Jumper, Boxer

The Fiat Ducato, Citroën Jumper and Peugeot Boxer share the same platform, so we offer an identical shelving system for them, divided by side and body version. If you have one of these three vehicles, continue to the shared page Ducato, Jumper, Boxer van racking.

What the racking consists of

The basis is a modular aluminium kit. Every profile has a clamping slot along its entire length, so you can anchor shelves, drawers, handles and your own accessories anywhere on the structure and change their position even after installation, without drilling into the profile again. Depending on your brief we supplement it with, for example:

  • Euro box shelving – a column structure with levels for 400×300 mm Euro boxes,
  • aluminium pull-out frames with spring locking for plastic crates, systainers or your own cases,
  • steel drawers,
  • shelves with organisers, bins or folding doors.

The system can be extended in every direction, so the racking can be added to later, and a damaged shelf component is replaced individually – you do not have to buy a whole new one. We have been supplying turnkey racking and conversions since 2009.

Professional installation and anchoring

Professional installation is an optional service. We provide it in Prague, in Slavičín in the Zlín region or directly at the customer's premises, but you do not have to order it – the shelving unit is a kit made of aluminium profiles, so you can also assemble it yourself after delivery.

Bear in mind that the structure is anchored to reinforced parts of the body, namely the side panels and the floor. Professional installation therefore includes drilling into these places in compliance with type-approval requirements – vans of this type have very few original anchor points. After professional installation, the procedure also includes registering the racking in the vehicle's electronic technical certificate (ISTP of the Ministry of Transport).

Cannot find your make or model?

The overview page shows the makes that have their own page. If you do not see your vehicle among them, tell us what vehicle it is and we will advise you individually. All you need to send is a hand sketch or a simple description of what you want to carry; we will design a 3D model that you can view and have adjusted until it is exactly as you imagine.

If you are looking for a solution by trade rather than by make of vehicle, also take a look at the racking for electricians and for plumbers.

Solutions by vehicle

What goes into the van is decided by three things: the length of the cargo space, its height and the height of the rear opening. The version codes tell you about the first two. L stands for the length of the body (L1 is the shortest) and H for the roof height (H1 low, H2 medium, H3 high). The third figure is just as important: the shelving unit has to pass through the rear doors, so its maximum possible height is determined by the height of the rear cargo opening, not by the ceiling of the cargo space. On taller versions the opening is lower than the ceiling.

On top of that come the position of the wheel arches, the shape of the side walls, ribs, mounts and the manufacturer's own equipment. That is why every made-to-measure racking is designed for the specific vehicle and body version.

We make racking for the most common vans on our market. The Fiat Ducato, Citroën Jumper and Peugeot Boxer share the same platform, so we offer an identical shelving system for them, divided by the side of the vehicle (left, right) and by body version, supplemented by a shelving unit for the bulkhead behind the cab. Their smaller siblings, the Fiat Doblò and Citroën Jumpy, have their own dimensional range and the solution for them is based rather on System 30. For the Ford Transit Custom and Toyota ProAce we make individual racking to the millimetre to the dimensions of the cargo space, and for the large Ford Transit the solution is different, because its cargo space is different.

Other vehicles for which we are preparing assemblies are the Mercedes Sprinter and Vito, Renault Master and Trafic, Opel Movano and Vivaro, Volkswagen Crafter, Transporter and Caddy, MAN and Iveco Daily. For newer electric versions of these vehicles the same applies as for combustion-engine ones, with the added considerations described in the chapter on electric vans.

Cannot find your vehicle? Send us the make, model, year of manufacture, the length and height of the body and a list of what you carry. We can design a solution even for vehicles that are not on the list.

Frequently asked questions

Does professional installation involve drilling into the vehicle body?
Yes. Professional installation includes drilling into reinforced parts of the body (side panels, floor) in line with type-approval requirements; vans have very few original anchor points. The aluminium profile itself, by contrast, is not drilled again; its clamping slot is used instead.

Is professional installation compulsory?
No. You can order professional installation from us, or assemble the shelving unit yourself after delivery.

Zadejte nám nezávaznou poptávku:

Napište nám, ozveme se vám na uvedený e-mail.

Přílohy, skica, apod.: Každý soubor nejvýše 2 MB, nejvýše 3 soubory.